Devices You Need to Install a New Bathtub
Devices You Need to Install a New Bathtub
Blog Article
Here down the page you can locate lots of superb additional info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bath tub isn't specifically brain surgery, however it does call for solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately hard task. If the old tub is readily available, the project can move immediately; if you have to open a wall to remove the old tub and also position the brand-new bathtub, the job is much harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub and set in the new one. Ensure you have actually qualified on your own for the task as well as fit trying it. Rather than hiring a professional to take control of a halfway-completed task, it is better to consider utilizing one before you start. Opportunities are you may require a professional plumber to make tube connections.
This article will certainly help you install a brand-new bathtub in your shower room if you have actually already acquired a new bathtub and do not require to change the setup of your previous water supply pipes.
Your devices as well as material checklist need to make up the following:
Getting ready for the Installment
First of all, the sustaining frame supplied with the bath should be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the versatile faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize all of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its last position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is separate the supply of water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be fairly problematic because of the limited access that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will come from the pipelines. Once the supply pipelines have been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wooden boards are helpful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level and also changing the feet on the bath tub until the level reads level.
To mount taps, fit all-time low of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water system and inspect all joints and new pipework for leakages as well as tighten them if needed. Load the bath tub as well as additionally check the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub ought to wait up until the tub has actually been used at least when as this will settle it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin making sure that the washers are in place between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former type needs to be linked to the tap ends first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to break a stiff seal, creating the water to penetrate the wall between the bathroom and also the tiling, leading to complications with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched paper or soft rope. Remember to constantly load the tub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can break rather early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily available on the market. It is recommended to fit the floor tiles utilizing water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that article about A Step-by-Step Guide to Installing a Bathtub through someone on our other site. So long as you appreciated our page if you please be sure to pass it around. I praise you for your time. Don't forget to pay a visit to our blog back soon.
Maintenance Sign-Up
Report this page